BOSS VE-500 Vocal Performer Vocal Effects Unit

BOSS VE-500 Vocal Performer Vocal Effects Unit

RADIAL CATAPULT Rx4 Cat5 4-channel Audio Snake

RADIAL CATAPULT Rx4 Cat5 4-channel Audio Snake

RADIAL CATAPULT Tx4 Cat5 4-channel Audio Snake

CA$159.99
Out Of Stock
SKU
206071
  • Catalog #: R800 8022






Note: Stock availability may not be accurate, please contact your preferred location to confirm.   


Vancouver Store
728 Granville St.
Vancouver, BC, V6Z 1E4
604-685-8471
  Contact Store Out Of Stock

Coquitlam Store
2560 Barnet Hwy.,
#116 Coquitlam, BC, V3H 1W3
604-941-8447
  Contact Store Out Of Stock

Langley Store
19638 Fraser Highway
Langley, BC, V3A 4C5
604-532-8303
  Contact Store Out Of Stock

North Vancouver Store
#800-801 Marine Drive
North Vancouver, BC, V7P 3K6
604-988-9974
  Contact Store Out Of Stock

Surrey Store
#157-10090 152nd Street
Surrey, BC, V3R 8X8
604-588-3200
  Contact Store Out Of Stock

Richmond Store
#150-3631 No. 3 Road
Richmond, BC, V6X 2B9
604-273-6661
  Contact Store Out Of Stock

Victoria Store
#105-2401D Millstream Road
Victoria, BC, V9B 3R5
250-383-5222
  Contact Store Out Of Stock

Nanaimo Store
#10-6894 Island Hwy. North
Nanaimo, BC, V9V 1P6
250-390-2626
  Contact Store Out Of Stock

4-Channel Cat 5 Audio Snake 

The Catapult TX4 and RX4 act like a typical four-channel analog audio snake; they allow you to send mic or line-level signals from one location to another without signal loss, noise, or interference, and without any digital audio conversion needed. What makes the Catapult system unique is that it utilizes Cat 5 Ethernet cable, which is widely available, lightweight, and economical. Simply connect a shielded Cat 5 cable between any two Catapult modules and they will use the analog conductors in the cable to deliver four balanced audio lines to any destination.

Straight-wire passive operation

Catapult modules require no power to operate, and since they keep the signal in the analog realm, no digital conversion is necessary. Straight-wire connection from the XLRs to the RJ45 connector on a Cat 5 cable ensures that your audio passes through without coloration or distortion.

Utilize pre-existing cable installations

As many buildings are already pre-wired for Cat 5, you can take advantage of this to transmit audio between distant rooms without the need to install or supply new cabling. This eliminates the need for bulky and expensive multi-channel audio cable, and allows contractors to benefit from installed network cable and easily connect from one room to another.

Mix & Match to add transformer isolation

All of the Radial Catapult modules are compatible with each other, and each is sold individually, so you can select whichever combination best suits your needs. The Catapult RX4 and TX4 can be used together as a pair, creating a 4-channel audio snake. However, if you need transformer isolation to prevent hum and buzz when splitting audio signals, two additional models of Catapults are available. The TX4L and RX4L have line level isolation transformers for splitting playback tracks or outputs to amp racks, while the TX4M and RX4M can be employed when splitting mic signals on stage. Use any combination of these six models, along with the compact Catapult Mini RX and TX to create a custom snake designed for your unique application.

Using the Catapult as a return snake

The Catapult is the perfect return snake for corporate events where you need to run a couple of lines back to the stage and monitors. Use the RX4L line isolation module to eliminate ground loops. 

Using the Catapult as a sub snake on stage

Cleaning up the stage while lowering the set-up times have become essential components in production. Use the Catapult at the front of the stage or next to the amps to create zones for quick deployment.

Using the Catapult as a 4-channel mic splitter

Use the Catapult TX4M to split the mics between the monitor desk and front of house with Eclipse transformer isolation to deliver a noise-free signal, saving hours of tedious trouble shooting.

Using the Catapult as a line isolator

The Catapult RX4L is the perfect 4-channel line isolator. Simply connect it in line with any line audio device to eliminate hum and buzz caused by ground loops.

Using the Catapult to network audio

Use the pre-existing Cat 5 or Cat 6 wiring in the building to network audio from one room through the walls to another. The XLR connections at each end make it easy!

Run four AES signals across Cat 5 cable platform

110 Ohm AES signals can easily travel across Cat 5 and Cat 6 Ethernet cable. Connect to the four Catapult TX4 XLRs for eight channels of audio for remote recording.

Features

  • Send four channels of analog audio over a single Cat 5/6 cable
  • Works with a building’s existing cable infrastructure
  • Choice of direct-wired or transformer isolated splits
  • Economical Cat 5/6 cable replaces bulky multi-channel audio snakes

Specifications

Audio circuit type:

Passive splitter

Frequency response:

7Hz ~ 20KHz

Dynamic range:

140dB

Total harmonic distortion:

0.0005% @ 1kHz

Common Mode Rejection Ratio:

>103dB

Maximum Input:

+35dBu

Features

Ground lift

Input Connectors:

XLR, RJ45

Output Connectors:

XLR, RJ45

General

Construction:

14 gauge steel chassis & outer shell

Size (L x W x D):

L: 8 1/8 x W: 4 1/8 x H: 2

Weight:

2.6 LBS

Shipping size (L x W x D):

L: 11 x W: 5 x H: 2.75

Shipping weight:

2.9 LBS

Power:

Passive, no power required 

Conditions:

For use in dry locations only between 5°C and 40°C

Warranty:

Radial 3-year, transferable

Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account